蒋秋云18924675756
PARAMETER | VALUE | UNIT |
Overall dimensions Width Height Depth |
98.70 +/-0.2 160.8 +/-0.2 2.00 +/-0.1 |
mm mm mm |
Screen size (diagonal) | 7.02 | inch |
Active area dimensions Width Height |
94.50 151.20 |
mm mm |
Display resolution | 1200 x 3 x 1920 WUXGA | Pixels |
Aspect ratio | 10:16 | |
Pixel dimensions Horizontal Vertical Pixel per Inch |
0.07875 0.07875 323 |
mm mm PPI |
Pixel arrangement | RGB Vertical stripe | |
Display colors | 16.7M | colors |
Display mode | Normally Black | |
Driver IC | R69429 | |
Driver RAM size | RAMLESS | |
Light Source | LED Backlight | |
Interface | MIPI, 4-line | |
Supply voltage module AVDD AVEE |
+5.5 (5.3~ 5.7) -5.5 (-5.7~-5.3) |
V V |
Interface Supply voltage | +1.8 (1.7~1.9) | V |
Power consumption module Panel (TFT LCD) Backlight Unit |
0.17 max 1.28 max |
W W |
Advised viewing direction | Free | |
Maximum contrast ratio (peak viewing angle) | 1200:1 | |
Typical luminance | 220 | Cd/m2 |
Backlight lifetime (Continuous operation at 25C; ILED =+15mArms) | Min. 15000 | hours |
Operating temperature range | -10 to +60 | oC |
Storage temperature | -30 to +70 | oC |
Response speed (typical) | 25 | ms |
Module mass (without external flexible foil cable) | t.b.d. | g |
SYMBOL | PIN | I/O | DISCRIPTION |
NC | 1 | - | No Connection |
VDD1V8 | 2 | P | Power supply for system ,IOVCC=1.8V |
VDD1V8 | 3 | P | Power supply for system ,IOVCC=1.8V |
GND | 4 | P | Ground |
Reset | 5 | P | System Reset pin |
NC | 6 | - | No Connection |
GND | 7 | P | Ground |
MIPI_D0_N | 8 | I/O | Negative MIPI differential Data Input 0 |
MIPI_D0_P | 9 | I/O | Positive MIPI differential Data Input 0 |
GND | 10 | P | Ground |
MIPI_D1_N | 11 | I | Negative MIPI differential Data Input 1 |
MIPI_D1_P | 12 | I | Positive MIPI differential Data Input 1 |
GND | 13 | P | Ground |
MIPI_CLK_N | 14 | I | Negative MIPI differential Clock Input |
MIPI_CLK_P | 15 | I | Positive MIPI differential Clock Input |
GND | 16 | P | Ground |
MIPI_D2_N | 17 | I | Negative MIPI differential Data Input 2 |
MIPI_D2_P | 18 | I | Positive MIPI differential Data Input 2 |
GND | 19 | P | Ground |
MIPI_D3_N | 20 | I | Negative MIPI differential Data Input 3 |
MIPI_D3_P | 21 | I | Positive MIPI differential Data Input 3 |
GND | 22 | P | Ground |
HS | 23 | O | Horizontal scan Signal for touch |
VS | 24 | O | Vertical scan Signal for touch |
GND | 25 | P | Ground |
TE | 26 | O | Tearing effect output signal for NVM(OTP),Let it open when not in use |
PWMO | 27 | O | PWM control signal for LED driver (CABC) |
BIST | 28 | I | Enables the Test Image Generation function, if not used, connect to ground |
NC | 29 | - | No Connection |
GND | 30 | P | Ground |
LED- | 31 | P | LED Cathode |
LED- | 32 | P | LED Cathode |
NC | 33 | - | No Connection |
VSN | 34 | P | Analog supply negative voltage |
VSN | 35 | P | Analog supply negative voltage |
NC | 36 | - | No Connection |
VSP | 37 | P | Analog supply positive voltage |
VSP | 38 | P | Analog supply positive voltage |
LED+ | 2 | P | LED Anode |
LED+ | 3 | P | LED Anode |
If=140mA;Vf=18.2V 3串7并
结构变更如下几点:
1、视窗尺寸按照新的显示屏修改;
2、右上角LOGO距离视窗太近,往上移动1mm
3、FPC绑定位置距离视窗太近,FPC整体往上移动1mm
*备注:玻璃基材:1.1mm Sodalime (苏打) 透过率≧86% LENS表面硬度≧6H;
超薄菲林结构建议整机结构尽量避让功能走线区域,避免频繁按压.
SENSOR 共用MCT4F2969-V3DSN-1的网具
1)OPERATING TEMP: -10°C~60°C
2)STORAGE TEMP : -20°C~70°C
3)GENERAL TOLERANCE: ±0.2
4)IC TYPE:GT911
5)玻璃基材:1.1mm Sodalime (苏打)基材;
6)FPC绑定位避免受压; 未注倒角统一按C 0.15*0.15mm
7)THE GAPE BETWEEN LCD AND CTP SHOULD BE OVER 0.5MM